This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision Next revision Both sides next revision | ||
zeiss_lsm_880 [2016/04/05 00:35] bioimaging [Objectives] |
zeiss_lsm_880 [2016/04/05 00:38] bioimaging [Microscope Turn Off Procedure] |
||
---|---|---|---|
Line 71: | Line 71: | ||
^ Position ^ Filterset ^ Reference ^ Excitation ^ Emission ^ | ^ Position ^ Filterset ^ Reference ^ Excitation ^ Emission ^ | ||
- | | 1 | Green | [[https://www.micro-shop.zeiss.com/?s=163176628fcf844&l=en&p=us&f=f&a=v&b=f&id=000000-1031-346&o=|FS38]] | 450-490 nm | 500-550 nm | | + | | 1 | Green | [[https://www.micro-shop.zeiss.com/?s=7139069fdc79c&l=en&p=us&f=f&a=v&b=f&id=489038-9901-000&o=|FS38HE]] | 450-490 nm | 500-550 nm | |
| 2 | Red | [[https://www.micro-shop.zeiss.com/?s=163176628fcf844&l=en&p=us&f=f&a=v&b=f&id=000000-1114-101&o=|FS43]] | 533-558 nm | 570-640 nm | | | 2 | Red | [[https://www.micro-shop.zeiss.com/?s=163176628fcf844&l=en&p=us&f=f&a=v&b=f&id=000000-1114-101&o=|FS43]] | 533-558 nm | 570-640 nm | | ||
| 3 | Blue | [[https://www.micro-shop.zeiss.com/?s=163176628fcf844&l=en&p=us&f=f&a=v&b=f&id=488049-9901-000&o=|FS49]] | G 365 nm | 420-470 nm | | | 3 | Blue | [[https://www.micro-shop.zeiss.com/?s=163176628fcf844&l=en&p=us&f=f&a=v&b=f&id=488049-9901-000&o=|FS49]] | G 365 nm | 420-470 nm | | ||
Line 79: | Line 79: | ||
* Turn on the two switches: ''SYSTEMS/PC'' and ''COMPONENTS'' | * Turn on the two switches: ''SYSTEMS/PC'' and ''COMPONENTS'' | ||
{{zeiss_lsm_880_1.jpg?100}} | {{zeiss_lsm_880_1.jpg?100}} | ||
- | * Turn the metal halide power source on (if needed) | ||
- | {{:bioimaging:halide_710.jpg?80}} | ||
- | * Turn the Ar laser on using the key (if needed) | ||
- | {{:bioimaging:laser_key_710.jpg?100}} | ||
* Turn the computer on | * Turn the computer on | ||
* Login with your unit account | * Login with your unit account | ||
* Wait for network icon to change to ''connected'' state | * Wait for network icon to change to ''connected'' state | ||
- | * Switch the Ar laser from ''idle'' ton ''run'' (don't change the ''current'') | + | * Start the ''ZEN'' software |
- | {{:bioimaging:laser_run_710.jpg?100}} | + | |
- | * Start the ''ZEN 2009'' software | + | |
===== Microscope Turn Off Procedure ===== | ===== Microscope Turn Off Procedure ===== | ||
If there's another user for this microscope in the next hour: | If there's another user for this microscope in the next hour: | ||
- | * Close the software, leave the lasers on an log off the computer. | + | * Close the software, leave the lasers on and log off the computer. |
- | * Clean up any objective were you used immersion oil. | + | * Clean up any objective where you used immersion oil. |
* **Make sure that there really is another user going to use the microscope.** | * **Make sure that there really is another user going to use the microscope.** | ||
Else: | Else: | ||
- | * Turn off the 561 nm laser and incubator in the software (if used) | + | * Turn off the lasers on ''ZEN'' |
- | * Switch the Ar laser from ''run'' to ''idle'' (if used) | + | |
- | * Turn off the Ar laser using the key (if used) | + | |
* Clean up any objective were you used immersion oil. | * Clean up any objective were you used immersion oil. | ||
* Exit the software, shut down the computer. | * Exit the software, shut down the computer. | ||
- | * Turn off the metal halide lamp | ||
* Turn off the main switches ''SYSTEMS/PC'' and ''COMPONENTS'' | * Turn off the main switches ''SYSTEMS/PC'' and ''COMPONENTS'' | ||
* Wait 5 min. for Ar laser cooldown | * Wait 5 min. for Ar laser cooldown | ||
* Turn off the ''MAIN SWITCH''. | * Turn off the ''MAIN SWITCH''. | ||
+ | |||
---- | ---- | ||
[[resources|Back to the Resources page]] | [[resources|Back to the Resources page]] |