zeiss_lsm_710
Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision Next revision Both sides next revision | ||
|
zeiss_lsm_710 [2020/01/01 20:12] bioimaging [Microscope overview] |
zeiss_lsm_710 [2020/01/15 12:22] bioimaging [Microscope Turn Off Procedure] |
||
|---|---|---|---|
| Line 76: | Line 76: | ||
| * Turn on the two switches: ''SYSTEMS/PC'' and ''COMPONENTS'' | * Turn on the two switches: ''SYSTEMS/PC'' and ''COMPONENTS'' | ||
| {{switches_710.jpg?100}} | {{switches_710.jpg?100}} | ||
| - | * Turn the metal halide power source on (if needed) | + | * Turn on the metal halide fluorescent light source (if needed) |
| {{halide_710.jpg?80}} | {{halide_710.jpg?80}} | ||
| - | * Turn the Ar laser on using the key (if needed) | + | * Turn on the Ar laser using the key (if needed) |
| {{laser_key_710.jpg?100}} | {{laser_key_710.jpg?100}} | ||
| - | * Turn the computer on | + | * Turn on the computer |
| + | * Log in to Windows (Bioimaging User) | ||
| * Login with Bioimaging User account | * Login with Bioimaging User account | ||
| - | * Wait for network icon to change to ''connected'' state | + | * Check that the computer is connected to an ''Unidentified network'' (click on the network icon in the taskbar) |
| + | {{::network_icon.png?200}} | ||
| * Switch the Ar laser from ''idle'' ton ''run'' (don't change the ''current'') | * Switch the Ar laser from ''idle'' ton ''run'' (don't change the ''current'') | ||
| {{laser_run_710.jpg?100}} | {{laser_run_710.jpg?100}} | ||
| - | * Start the **ZEN 2012** software | + | * Start the **ZEN** software |
| ===== Microscope Turn Off Procedure ===== | ===== Microscope Turn Off Procedure ===== | ||
| - | If there's another user for this microscope in the next hour: | + | If there is another user for this microscope in the __next hour__: |
| - | * Close the software, leave the lasers on and log off the computer. | + | * Close **ZEN**, leave the lasers on, log off the computer |
| - | * Clean up any objective where you used immersion oil. | + | * Clean up immersion objectives |
| - | * **Make sure that there really is another user going to use the microscope.** | + | |
| Else: | Else: | ||
| * Turn off the 561 nm laser and incubator in the software (if used) | * Turn off the 561 nm laser and incubator in the software (if used) | ||
| * Switch the Ar laser from ''run'' to ''idle'' (if used) | * Switch the Ar laser from ''run'' to ''idle'' (if used) | ||
| * Turn off the Ar laser using the key (if used) | * Turn off the Ar laser using the key (if used) | ||
| - | * Clean up any objective were you used immersion oil. | + | * Clean up immersion objectives |
| - | * Exit the software, shut down the computer. | + | * Close **ZEN**, shutdown the computer. |
| - | * Turn off the metal halide lamp | + | * Turn off the metal halide fluorescence light source |
| - | * Turn off the main switches ''SYSTEMS/PC'' and ''COMPONENTS'' | + | * Turn off the two switches: ''SYSTEMS/PC'' and ''COMPONENTS'' |
| * Wait 5 min. for Ar laser cooldown | * Wait 5 min. for Ar laser cooldown | ||
| - | * Turn off the ''MAIN SWITCH''. | + | * Turn off the ''MAIN SWITCH'' |
| ---- | ---- | ||
| [[resources|Back to the Resources page]] | [[resources|Back to the Resources page]] | ||
zeiss_lsm_710.txt · Last modified: 2024/01/18 01:18 by bioimaging
Page Tools
